 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DS1035 3-in-1 High-Speed Silicon Delay Line www.dalsemi.com FEATURES All-silicon timing circuit Three independent buffered delays Stable and precise over temperature and voltage Leading and trailing edge precision preserves the input symmetry Standard 8-pin DIP and 8-pin SOIC (150 mil) Vapor phasing, IR and wave solderable Available in Tape and Reel PIN ASSIGNMENT IN1 IN2 IN3 GND 1 2 3 4 8 7 6 5 VCC OUT1 OUT2 OUT3 DS1035M 8-Pin DIP See Mech. Drawings Section IN1 IN2 IN3 GND 1 2 3 4 8 7 6 5 VCC OUT1 OUT2 OUT3 DS1035Z 8-Pin SOIC (150-mil) See Mech. Drawings Section PIN DESCRIPTION IN1-IN3 OUT1-OUT3 NC VCC GND (Sub) - Input Signals - Output Signals - No Connection - +5 Volt Supply - Ground - Internal substrate connection, do not make any external connections to these pins DESCRIPTION The DS1035 series is a low-power +5-volt high-speed version of the popular DS1013 and complements the DS1033 +3.3 Volt version. The DS1035 series of delay lines have three independent logic buffered delays in a single package. The device is Dallas Semiconductor's fastest 3-in-1 delay line. It is available in a standard 8-pin DIP and 150 Mil 8-pin Mini-SOIC. The device features precise leading and trailing edge accuracies. It has the inherent reliability of an allsilicon delay line solution. The DS1035's initial tolerance is 1.5 or 2.0 ns with an additional tolerance over temperature and voltage of 1.0 ns or 1.5 ns, depending on the delay value. Each output is capable of driving up to 10 LS loads. Standard delay values are indicated in Table 1. Customers may contact Dallas Semiconductor at (982) 371-4348 for further information. 1 of 6 111799 DS1035 LOGIC DIAGRAM Figure 1 PART NUMBER DELAY TABLE (tPLH , tPHL) Table 1 PART NUMBER DS1035-60 DS1035-80 DS1035-10 DS1035-12 DS1035-15 DS1035-20 DS1035-25 DS1035-30 DELAY PER OUTPUT (ns) 6/6/6 8/8/8 10/10/10 12/12/12 15/15/15 20/20/20 25/25/25 30/30/30 INITIAL TOLERANCE 1.5 ns 1.5 ns 1.5 ns 1.5 ns 1.5 ns 1.5 ns 2.0 ns 2.0 ns TOLERANCE OVER TEMPERATURE AND VOLTAGE 1.0 ns 1.0 ns 1.0 ns 1.0 ns 1.5 ns 1.5 ns 1.5 ns 1.5 ns NOTES: 1. Nominal conditions are +25C and VCC=+5.0 volts. 2. Temperature range of 0C to 70C and voltage range of 4.75 volts to 5.25 volts. 3. Delay accuracy is for both leading and trailing edges. 2 of 6 DS1035 TEST SETUP DESCRIPTION Figure 2 illustrates the hardware configuration used for measuring the timing parameters of the DS1035. The input waveform is produced by a precision pulse generator under software control. Time delays are measured by a time interval counter (20 ps resolution ) connected to the output. The DS1035 output taps are selected and connected to the interval counter by a VHF switch control unit. All measurements are fully automated with each instrument controlled by the computer over an IEEE 488 bus. DS1035 TEST CIRCUIT Figure 2 3 of 6 DS1035 ABSOLUTE MAXIMUM RATINGS* Voltage on Any Pin Relative to Ground Operating Temperature Storage Temperature Soldering Temperature Short Circuit Output Current -1.0V to +7.0V 0C to 70C -55C to +125C 260C for 10 seconds 50 mA for 1 second * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. DC ELECTRICAL CHARACTERISTICS PARAMETER Supply Voltage Active Current High Level Input Voltage Low Level Input Voltage Input Leakage High Level Output Current Low Level Output Current SYMBOL VCC ICC VIH VIL IL IOH IOL 0VVIVCC VCC=4.75V VOH=4V VCC=4.75V VOL=0.5V VCC=5.25V Period=1s TEST CONDITION (0C to 70C; VCC =+5V 5%) MIN 4.75 TYP 5.00 MAX 5.25 35 2.2 -0.5 -1.0 VCC +0.5 0.8 +1.0 -1.0 12 UNITS V mA V V A mA mA AC ELECTRICAL CHARACTERISTICS PARAMETER Period Input Pulse Width Input-to-Tap Output Delay Output Rise or Fall Time Power-up Time SYMBOL tPERIOD tWI tPLH, tPHL tOR, tOF tPU MIN 2 (tWI) 100% of Tap Delay Table 1 2.0 TYP (+25C; VCC =5V 5%) MAX UNITS ns ns ns 2.5 100 ns ms NOTES 3 3 CAPACITANCE PARAMETER Input Capacitance SYMBOL CIN MIN TYP MAX 10 (TA =25C) UNITS NOTES pF 4 of 6 DS1035 Ambient Temperature: 25C =3C Supply Voltage (VCC): 5.0V =0.1V Input Pulse: High: 3.0V =0.1V Low: 0.0V =0.1V Source Impedance: 50=max. Rise and Fall Time: 3.0 ns max. - Measured between 0.6V and 2.4V. Pulse Width: 500 ns Pulse Period: 1 s Output Load Capacitance: 15 pF Output: Each output is loaded with the equivalent of one 74F04 input gate. Data is measured at the 1.5V level on the rising and falling edges. Note: The above conditions are for test only and do not restrict the devices under other data sheet conditions. TEST CONDITIONS TIMING DIAGRAM NOTES: 1. All voltages are referenced to ground. 2. @ VCC=5 volts and 25C, delay accuracy on both the rising and falling edges within tolerances given in Table 1. 3. Pulse width and duty cycle specifications may be exceeded; however, accuracy will be application sensitive with respect to decoupling, layout, etc. 5 of 6 DS1035 TERMINOLOGY Period: The time elapsed between the leading edge of the first pulse and the leading edge of the following pulse. tWI(Pulse Width): The elapsed time on the pulse between the 1.5 volt point on the leading edge and the 1.5 volt point on the trailing edge, or the 1.5 volt point on the trailing edge and the 1.5 volt point on the leading edge. tRISE(Input Rise Time): The elapsed time between the 20% and the 80% point on the leading edge of the input pulse. tFALL(Input Fall Time): The elapsed time between the 80% and the 20% point on the trailing edge on the input pulse. tPLH(Time Delay, Rising): The elapsed time between the 1.5 volt point on the leading edge of the input pulse and the 1.5 volt point on the leading edge of the output pulse. tPHL(Time Delay, Falling): The elapsed time between the 1.5 volt point on the falling edge of the input pulse and the 1.5 volt point on the falling edge of the output pulse. 6 of 6 |
Price & Availability of DS1035
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |